How often values from TCW are refreshed (that is state of outputs, etc.). The value in seconds.
User interface language
Uptime 0 sec, 0 min, 0 hour, 0 day Time 0 Version: | HW VCC = V Temperature = °C
Outputs
PWM Out's
Analog sensors
---
---
---
---
---
---
Temperature sensor
DS1
---
°C
DS2
---
°C
DS3
---
°C
DS4
---
°C
DS5
---
°C
DS6
---
°C
DS7
---
°C
DS8
---
°C
T1
---
°C
H1
---
%
P1
---
hPa
Other sensor
PM1.0
---
ug/m3
PM2.5
---
ug/m3
PM4.0
---
ug/m3
PM10.0
---
ug/m3
CO2
---
ppm
The difference of measurements
DIFF1
DIFF2
Digital inputs
INPD1
1
INPD2
1
INPD3
1
INPD4
1
Power/Energy
P/E1
---
kW
---
kWh
P/E2
---
kW
---
kWh
P/E3
---
kW
---
kWh
P/E4
---
kW
---
kWh


Time of return

Periodic switching

Set the output after starting

Keep state after restart

Analog sensors
---
---
Calibration
Multiplier
---
---
Calibration
Multiplier
---
---
Calibration
Multiplier
---
---
Calibration
Multiplier

Temperature Sensors
DS1
°C
DS2
°C
DS3
°C
DS4
°C
DS5
°C
DS6
°C
T1
°C
H1
%
P1
hPa
Calibr. [m]

Digital inputs
INPD1
1
INPD2
1
INPD3
1
INPD4
1

Logic operations

ABAND
000
010
100
111
ABOR
000
011
101
111
ABNOR
001
010
100
110
ABNAND
001
011
101
110
ABXOR
000
011
101
110

Event list

#SourceIfValueStateOperatorActionOff delay
1

Scheduler list
#NameOutputValueTimeDate/Day
1

MQTT DISCONNECTED

??????

1Wire Sensors

DS1
DS2
DS3
DS4
DS5
DS6
DS7
DS8

I2C Sensors

kHz

Firmware Upgrade

You have one minute to put new firmware file by TFTP, after this time TCW will run normally.


WWW Upgrade

To use WWW Upgrade you must first uncheck Authentication Enabled in Access tab.

Please specify a specially prepared binary file to upload www into flash.


Backup and restore

Backup creation

Generate binary file with backup of current TCW settings.


Restoring settings from backup
To use Restore settings from backup you must first uncheck Authentication Enabled in Access tab.

Please select backup file and then confirm with button below. Note that settings will be restored after TCW restart.

Restore the default settings
Attention!

Bootloader has been started and will be active for 60 seconds.

Bootloader is no longer active.

Reload page

Please wait a while.

WWW upgrade has been finished. To see changes you should reload page.

Reload page

Restoring settings in progress - please wait.

To finish restoring the settings you have to restart the device.

Restarting device in progress, please wait for redirect.

W1 W2 W3 W4 W5 W6
Enabled
off
off
off
off
off
off
Send email
Output
Host/IP
Ping time [ms] 0 0 0 0 0 0
Ping failures 0 0 0 0 0 0
Ping wait time [s]
Ping period
Wait after restart
Restart time
Limit of restarts 0 0 0 0 0 0
State of output 0 0 0 0 0 0
Delay start after power on
GSM DISCONNECTED GSM NOT REGISTER TO NETWORK

Recipient's number
Recipient's number
Recipient's number
Recipient's number
Uptime 0 sec, 0 min, 0 hour, 0 day Time 0 Version: | HW VCC = V Temperature = °C
---
---
---
---
---
---
---
°C
---
°C
---
°C
---
°C
---
°C
---
°C
---
°C
---
°C
---
°C
---
%
---
hPa
CO2
---
ppm
PM1.0
---
ug/m3
PM2.5
---
ug/m3
PM4.0
---
ug/m3
PM10.0
---
ug/m3
DIFF1
DIFF2
1
1
1
1
P/E1
---
kW
---
kWh
P/E2
---
kW
---
kWh
P/E3
---
kW
---
kWh
P/E4
---
kW
---
kWh
Attention!

Confirm sending command?